Cast Burners, Pipe Burners. High Heat Cast Iron Propane Burners,Venturi

High Pressure Propane Cast Burners and Pipe Burners We sell high quality cast iron propane burners. Each one of our cast burners, pipe burners, and jet burners are bench tested and optimized for high gas efficiency. Outdoor cookers normally use high pressure burners because they give you much higher heat output that a low pressure burner. LOW PRESSURE burners require either natural gas or a low pressure propane gas regulator if your fuel source is a propane tank. Propane supplied in a trailer home or RV normally has the propane gas already adjusted to a very low pressure at the propane source. LOW PRESSURE burners give heat comparable to that of a gas stove top burner in your kitchen. Preset LOW PRESSURE propane regulators are set at 6 ounces. Natural gas pressure in most areas is 10 ounces and requires only a on/off valve to attenuate the flame. We also sell custom pipe burners. See Additional Needle Control Valves with custom Gas Orifices in the GAS ORIFICE FITTINGS section. We ship everywhere in the world... and the shipping is free to the 48 contiguous US states.

Cast Iron Burner - Cast iron burners are the heart of any propane cooker. In every test we conducted these high pressure propane cast iron burners out performed every other similar propane cast burner we have tried. This is the highest quality, highest performance, and the best looking cast iron propane burner we have ever sold. It produces up to 160,000 BTU/hr and does so in an evenly directed manner. Like the HPCAST6 and HPB6 units this propane cast burner comes with a 3/8" flare fitting and an air shutter. We have also outfitted these cast iron propane burners with our Insect Guard screen. Most outdoor cooking appliances are usually stored in areas where small insects, such as spiders and "dirt dobbers" set up housekeeping. These insects have an annoying habit of building their nest inside small dark places, which includes the inside of a cast iron burner. Any obstruction in the cast causes a reduction in its performance and requires the propane cast burner to be disassembled and cleaned. Our Insect Guard screen helps prevent this problem. Optimum working distance from top of cast to bottom of heated surface is 4 to 5". Diameter of burner head is 4". Height from base of cast to top of burner is 3 1/4". Distance from center of burner bolt at bottom of burner to air inlet at the edge of the cast is 5". Distance from bottom edge of cast burner head to air inlet at the edge of the cast is 3 1/2". Use COM#2 regulator/hose. Weight 5# Free shipping in 48 U.S. States.

<- Optional Needle Control Valve w/ Orifice, gas inlet position is adjustable.

HPOCA4

Cast Iron Burner - This high pressure propane cast iron burner produces up to 160,000 BTU/hr of heat quietly and efficiently and is similar to our HPOCA4 propane cast burner unit, but has a longer 6" neck. The propane burner comes with an air shutter and a 3/8" flare fitting. The bolt at the bottom of the propane cast burner head is a large 10mm. An Insect Guard screen is available as an optional extra. Optimum working distance from top of cast to bottom of heated surface is 4 to 5". Diameter of burner head is 4". Height from base of cast to top of burner is 3". Distance from center of burner bolt at bottom of burner to air inlet at the edge of the cast is 6 3/8". Distance from bottom edge of cast burner head to air inlet at the edge of the cast is 5". Use COM#2 regulator/hose. Weight 5# Free shipping.

Also available with a Needle Control Valve with Orifice:

HPB6

Cast Iron Burner - This popular design high pressure propane cast iron burner also produces up to 160,000 BTU/hr of heat quietly and efficiently. The propane burner comes with an air shutter and a 3/8" flare fitting. The bolt at the bottom of the propane cast burner head is either 6mm or 1/4". An Insect Guard screen is available as an optional extra. Optimum working distance from top of cast to bottom of heated surface is 4 to 5". Diameter of burner head is 4". Height from base of cast to top of burner is 3". Distance from center of burner bolt at bottom of burner to air inlet at the edge of the cast is 6 5/8". Distance from bottom edge of cast burner head to air inlet at the edge of the cast is 4 1/2".Use COM#2 regulator/hose. Weight 5# Free shipping.

<- Optional Needle Control Valve w/Orifice, gas inlet position is adjustable.

HPCAST6

Premium Two-Part Cast Iron Burner - Adjustable Length Neck High pressure adjustable length two piece premium cast burner and venturi. Our finest and most efficient high pressure cast burner and venturi design. The distance between the burner head and venturi is determined by the length of the 3/4" black pipe nipple used. The black pipe nipple is NOT included. Both the cast burner and the venturi have 3/4" female normal pipe thread inlets. This unique burner is ideal for applications where the venturi is best placed outside or farther away from the confined area where the burner is installed. The pipe run should be straight with no elbows. This cast produces up to 160,000 BTU and is supplied with an air shutter, insect screen guard, and 3/8" gas flare fitting. Optimum working distance from top of cast to bottom of heated surface is 4 to 5". The large bolt at the bottom of the cast burner is a 10 mm. Diameter of burner head is 4". Height from the base of cast to top of burner is 3 3/4". The bolt extend another 3/4". Use COM#2 regulator/hose Weight 5#. Free shipping.

. Gas assist for pit and grill builders

Also available with Needle Control Valve with Orifice.

HPGX-2

Cast Iron Premium Venturi Only High pressure premium cast venturi only. The extra large volume venturi permits maximum efficiency in mixing the air and gas. It has a 3/4" female normal pipe thread inlet. May be used in conjunction with a black drilled pipe nipple (a pipe burner) that is capped off or in a variety of special applications where the air and gas mixture is delivered to the burner tips. Use COM#2 regulator/hose An insect screen guard is included. Weight 13.1 oz. Free shipping. We can build custom length pipe burners. For information call 713 222 0077. Also available with a Needle Control Valve with Orifice as shown below:

Great to adjust flame height on custom Pipe Burners

HPGX-1

Custom Pipe Burners - We stock 32", 44", 56", and 68" pipe burners assemblies (as measured from one end of the pipe to the opposite end of the pipe's threads.) The pipes are 1.25"ID and 1.5"OD with a standard 3/16" pipe wall thickness. These assemblies include a threaded pipe cap at one end and a venturi at the other end. The first eight inches of the pipe is used as the "throat" of the burner and does not have any holes for flames. The 32" burner has 22" of flame, the 44" burner has 34" of flame, the 56" burner has 46" of flame, and the 68" burner has 58" of flame. In measuring your available space remember that the screw on pipe cap on the threads at the end of the pipe will add ~0.75" to the total length but you will lose a little of the total length in running the pipe through the wall of your cooker before you screw on the venturi. For supporting the assembly we recommend a cradle out of a well supported length of angle iron. A cradle support will permit easy removal of the burner unit for cleaning, when necessary. Our pipe burners have been engineered to give an even, high heat blue flame across the length of the pipe and they easily light. Don't waste your propane on a pipe burner that gives an inefficient yellow flame. Use COM#2 regulator/hose for propane. We also can provide any of these pipe burners for natural gas use. Weights: 32" -10#, 44"-12#, 56"-14#, 68"-16#. Free shipping. Also available with a Needle Control Valve with Orifice.

Call 713 222 0077 for info

PBM125

We can provide pipe burners for propane or natural gas use.

Custom Pipe Burner with Grease Shield All the above pipe burners can be purchased with a permanently welded grease shield. Our grease shields will add 3" to the height of the assembly. Use COM#2 regulator/hose Weights: 32"-14#, 44"-17#, 56"-21#, 68"-25#. Free shipping.

Call 713 222 0077 for info. Ask for James, our pipe burner specialist.

PBMG125

All pipe burners are bench tested and adjusted for optimum performance before shipping.

Custom Length Pipe Burners

-We can also install any number of custom support legs, if desired. Call for a quote. Free shipping Call 713-222-0077 and ask for James.

-Custom manifolds and a variety of control valve options are available. Just ask.

-Our custom pipe burners are used for a wide variety of applications, i.e., maple sugar evaporators, industrial evaporators, industrial conveyor systems, live steam production for trains, hog roasters, barbecue smoker pits, gas grills, gun barrel bluing, and corn roasters among many other applications. We can optimize our pipe burners for use with high or low pressure propane or natural gas so you don't waste expensive fuel.

CPB

Maximum Heat MONSTER Two-Part Cast Iron Burner - Adjustable Length Neck High pressure, adjustable-length, 225,000 btu/hr cast burner and venturi. Our proprietary MONSTER high pressure cast burner and venturi design is in a class by itself. The distance between the burner head and venturi is determined by the length of the 1 1/4" black pipe nipple used. The black pipe nipple is NOT included. Both the cast burner and the venturi have 1 1/4" female normal pipe thread inlets. This MONSTER burner is ideal for applications where Maximum High Heat is required, and where the venturi is to be placed outside of or farther away from the confined area where the burner is installed. The pipe run should be straight with no elbows. This cast can produce an incredible 225,000 but/hr and is supplied with an adjustable air shutter, insect screen guard, and the standard 3/8" male gas flare fitting for hose connection. This is one of the most efficient cast burners on the market. It does not waste the propane. The combustion is complete and the flames are directed where you want the heat. Optimum working distance from top of cast to bottom of heated surface is 4 to 5". The large bolt at the bottom of the cast burner is a hefty 10 mm diameter. Diameter of burner head is 6". Height of the burner (excluding the bolt) is 6 1/4". Use COM#2 regulator/hose Perfect for larger scale Home Brewing applications or crawfish boils where you just don't want to wait around. Weight 10#, excluding the pipe nipple. Free shipping.

comparison of sizes of HPMAX-2 and HPB6 cast burners The 160,000 btu/hr HPB6 burner compared with the 225,000 btu/hr HPMAX-2. Also available with a Needle Control Valve with Orifice as shown here:

HPMAX-2

This 10# MONSTER will get that big pot of water heated lickety-split...no fooling around! Serious heat.

Cast Iron MONSTER Venturi Only High pressure MONSTER cast venturi only. The extra large volume venturi permits maximum efficiency in mixing the air and gas. It has a 1 1/4" female normal pipe thread inlet. May be used in conjunction with a black drilled pipe nipple (a pipe burner) that is capped off or in a variety of specialty applications where the air and gas mixture is delivered to the burner tips. Use COM#2 regulator/hose An insect screen guard is included. For comparison the HPMAX-1 is shown next to a HPGX-1 below. Weight 2# 1 oz. Free shipping.

Also available with a Needle Control Valve with Orifice, shown here:

HPMAX-1

MONSTER Venturi

Low Pressure Burners may be powered by low pressure Propane (6 oz.) or Natural Gas (10 oz.). Low pressure cast burners will be shipped with propane orifices unless natural gas orifices are requested at the time of purchase.

Low Pressure Cast Iron Burner This low pressure cast burner is designed for lower temperatures and produces up to 40,000 BTU/hr of heat. The cast burner comes with an air shutter and a 90 degree angled 3Propane Regulator for Propane Gas Regulation/8" flare fitting. A straight fitting, as pictured, is available by request. Use with a COM#5UL Low Pressure preset regulator if using with propane. Natural gas version available by request at the same price. Optimum working distance from top of cast to bottom of heated surface is 4". An Insect Screen Guard screen is available as an optional extra. Dimensions: L-9 1/2", W-5 3/4", H- 2 1/2", Diameter. 5 3/4". Weight 5#. Free Shipping.

<-Optional Needle Control Valve w/Orifice, gas inlet position is adjustable.

LPCAST

34.95

Large Low Pressure Cast Iron Burner The dimensions of this larger low pressure cast burner are 10" diameter x 4 1/2" high x 15" long and with 10" distance from the center of the burner to the air inlet (neck length is therefore 5"). This heavy duty burner produces up to 100,000 BTU/hr and comes with mounting bolts on the outside ring. Use with a COM#5UL Low Pressure preset regulator if using with propane. Natural gas version available by request at the same price. Optimum working distance from top of cast to bottom of heated surface is 4". Insect screen guard is included. Weight 13#. Free shipping.

<- Optional Needle Control Valve w/ Orifice, gas inlet position is adjustable.

LPCAST10

97.50

The optional CVO250 Needle Valve Control Orifice fitting has the same gas hose connection threads as the standard orifice fitting normally supplied with this burner.

Large Low Pressure Two Part Cast Iron Burner The dimensions of this unique, adjustable length large low pressure cast burner are 10" diameter x 4 1/2" high. The distance between the burner head and venturi is determined by the length of the 1 1/4" black pipe nipple chosen by the user. The black pipe nipple is NOT included. Both the cast burner and the venturi have 1 1/4" female normal pipe thread inlets. This heavy duty burner produces up to 100,000 BTU/hr and comes with mounting bolts on the outside ring. Use with a COM#5UL Low Pressure preset regulator if using with propane. Natural gas version available by request at the same price. Optimum working distance from top of cast to bottom of heated surface is 4". Insect screen guard is included. Weight 13# 15 oz., excluding the pipe nipple. Free shipping.

Also available with a Needle Control Valve with orifice:

New Item, handy for smokehouse designs

LPCAST10-2

New Item

127.95

Insect Guard This screen helps prevent insects from nesting inside the propane cast burner head. It is standard on the HPOCA4 and is optional for the HPB6 and HPCAST6 propane burners. Picture at right shows the a screen installed on the air entrance to a venturi. Price is for the screen only. Net weight 0.1# Free shipping.

INSECT1

2.25